Robot Make 1
Robot Make 2
Robot Make 3
Robot Make 4
 
 


¢Á How to assemble 8051kit
 


1. Check all the components with the list.
2.
Devide the main board and the communication board.

.     


3. Put the LED into then solder. (Please be careful the direction.)

   ( Long leg(+) and short leg(-) )

   


3.Solder XTAL(Y1), 30pF ceramic condenser (C5,6), RA1(Array resistor 471),
104pF miler condenser(C1,2,3,7),  push button S/W(S1), 10K Resistor(R1), 10uF Electrolytic condenser(C4).

Solder 30pF ceramic condenser  obliquely and low becasue the 8051CPU goes high^^
Solder the array resistor and electrolytic condenser as the picture, please consider the direction.
The part which has a dot is common.
The electrolytic condenser which has a white line is a indication.Solder XTAL(Y1), 30pF ceramic condenser (C5,6), RA1(Array resistor 471),
104pF miler condenser(C1,2,3,7),  push button S/W(S1), 10K Resistor(R1), 10uF Electrolytic condenser(C4).

Solder 30pF ceramic condenser  obliquely and low becasue the 8051CPU goes high^^
Solder the array resistor and electrolytic condenser as the picture, please consider the direction.
The part which has a dot is common.
The electrolytic condenser which has a white line is a indication.

       

     

4. Solder the header pin male(J1, 2, 4, 5, JP1)and header pin female(J3, J6-communication board).

            

                /* Solder the header pin male J1 and J4 for the extension under the board.  */

5. Solder  IC socket U1, U2, U4, U5. At this time, cut the bottom of the U1 for the prevention of
the confliction with 30pF ceramic condenser. The IC socket which has a groove is for the IC1.

           


6. For the IC socket U3, prepare 4 round sockets with 14hole, solder as a 2-stages.

      

7.
Solder headerpin felmale J6, IC socket U6, connector male J7, J8 and 4 electrolytic condenser 22uFs.

      


8.
Put U1 into the 8051 or 8031(CPU), put  U2 into 74HC573(latch), put U4 into 61256(ram),
   on the top of them . put  U3 27C256(rom) and U5 into 16V8(gal), at the last. put U6 into MAX232
   (communication chip) as the direction to IC which has a dot or a groove to be upper.


     

Put LED on-and-off into J2. put 2 jumpers into JP1 vertically. (when you use 27C256,29C256)
   when put it horizontally, use 28C256.



9.
Combine the communication board and main board as the picture.

                   


11.
Make the communication cable..

  

  

 {
9 pin connector( No2 pin : red, No3 Pin : white, No5 Pin : black). }


   img1.gif    


11.
Put the power into. Be careful the direction. If the polarity is changed, the board will have vital defect.
 LEDs are lightening from upper 4 LEDs then lower 4 LEDs then all the 8 LEDs are turned on. It is normal
 operating. You should check the memory at the communication situation and download one file for make sure.

     





 

Address :150-094, 4 floors 8-1,Mullae 4 Dong, YongdungpoGu, Seoul, South Korea / Phone : +82-2-597-8224, Fax : +82-2-2679-8557
Copyright(C) 2000, Roboblock System Co., Ltd, All Rights Reserved / E-Mail : WebMaster